3D Model Database

Tip: Complementary lesson plans are available for 3D models marked with zavřít
Tip: Become a licensed YSoft BE3D eDee user.​ Premium 3D lesson plans for YSoft BE3D eDee users are available for 3D models marked with zavřít
Show filter Hide filter
Sort by: Result count  for
    : 195
    Cell Stand 4

    Cell Stand 4

    Phone stand

    Tall cell phone stand with a hole for a charger. Ideal for watching videos or movies in a portrait orientation. 
    CCBYNCSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: On
    Advanced settings: Default
    • Total print time 6 hours
    • Total filament 16.5 m
    • Additional non-printable components
    • Printed all at once
    Chair Stopper - End Cap

    Chair Stopper - End Cap

    Chair Stopper

    An end cap for the chair leg with a 26 mm inner diameter. The chair stopper will prevent the chair from damaging and scratching the floor.
    CCBYNCSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: 0.1 mm layer height
    • Total print time 2 hour
    • Total filament 1.5 m
    • Additional non-printable components
    • Printed all at once
    Coat Hook

    Coat Hook

    Wall mountable coat hook

    To get maximum strength, use 4 perimeters (1.6mm shell thickness).
    CCBYNCSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Shell thickness 1.6mm
    • Total print time 1 hour 15 minutes
    • Total filament 4 m
    • Additional non-printable components
    • Printed all at once
    Cocconeis

    Cocconeis

    Use in primary schools, secondary schools and universities. The model shows a siliceous cell wall of microscopic unicellular algae - diatoms.  These are two pennate diatoms, abundant in fresh waters, Navicula and Cocconeis. The basic structures of the shell (frustule) correspond to reality. The frustule consists of two parts that fit together like the lid and bottom of a box (separable, it is possible to add chloroplasts, nucleus, ...). Navicula has a raphe (slit) on each half of the frustule (Cocconeis only on one), and both diatoms have striae (pores in a line on the surface).
    Use in primary school: unicellular organisms, unicellular algae most widespread in fresh waters, it is possible to add chloroplasts, nucleus, etc., photosynthesis, movement, in the geological past of the Earth - formation of diatomaceous earth (filtration of beer, wine, building material, insulating material, dynamite, toothpaste), formation of oil (southern deposits) - from organic matter of diatoms.
    Use at secondary school, university: unicellular algae, pennate diatoms, construction of diatom frustule, from two parts (epitheca, hypotheca), raphe, striae, pores, movement of diatoms, determination of two representatives: Navicula, Cocconeis. Photosynthesis, function in the ecosystem, human use.
    CCBYSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: On
    Advanced settings: Default
    • Total print time 32 hours 5 minutes
    • Total filament 83.77 m
    • Additional non-printable components
    • Printed all at once
    COMMON PUFFBALL

    COMMON PUFFBALL

    The fruiting bodies of the Common Puffball are club-shaped and white or grey in colour. The surface is covered with nipples. When the spores are ripe, a bore opens at the top of the fruiting body, through which the spores are expelled. The inside of young fruiting bodies is white, while older fruiting bodies have a cottony brown flesh inside. The Common Puffball is an edible mushroom when young. It grows abundantly in groups in deciduous and coniferous forests, at the edge of paths, or in meadows.
    The models of the puffball show adult fruiting bodies. If they are printed with white filament, there is no need to finish them, just clean off any excess filament fibres.
    CCBYSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Brim
    • Total print time 34 hours 22 minutes
    • Total filament 160.23 m
    • Additional non-printable components
    • Printed all at once
    Creative Coastline

    Creative Coastline

    Print a box designed for interchangeable coastline feature models.

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: ON
    Advanced settings: ON
    • Total print time 18 hours
    • Total filament 50 m
    • Additional non-printable components
    • Printed all at once
    Credit Card Christmas Tree

    Credit Card Christmas Tree

    Christmas Tree

    Two flat pieces can be interconnected to become a self-standing Christmas tree. 
    CCBYSA

    Recommended print settings

    Print profile: Speed
    Initial platform: None
    Print supports: Off
    Advanced settings: Default
    • Total print time 40 minutes
    • Total filament 1.6 m
    • Additional non-printable components
    • Printed all at once
    Cress Head flower pot

    Cress Head flower pot

    Cress Head 1

    A simple design with a bucket-shaped head where the seeds will grow.
    CCBYSA

    Recommended print settings

    Print profile: Speed
    Initial platform: None
    Print supports: On
    Advanced settings: Default
    • Total print time 4 hours
    • Total filament 7.7 m
    • Additional non-printable components
    • Printed all at once
    Cress Head flower pot

    Cress Head flower pot

    Cress Head 2

    A sitting Cress Head with level arms outstretched. 
    CCBYSA

    Recommended print settings

    Print profile: Speed
    Initial platform: None
    Print supports: On
    Advanced settings: Default
    • Total print time 4 hours
    • Total filament 9.6 m
    • Additional non-printable components
    • Printed all at once
    Cress Head flower pot

    Cress Head flower pot

    Cress Head 3

    This Cress Head is standing with one foot lifted and the other attached to a round base.
    CCBYSA

    Recommended print settings

    Print profile: Speed
    Initial platform: None
    Print supports: On
    Advanced settings: Default
    • Total print time 6 hours
    • Total filament 16.5 m
    • Additional non-printable components
    • Printed all at once
    Cube connector

    Cube connector

    3D connector to contstruct different shapes using wooden dowl rods (or other suitable materials)

    Recommended print settings

    DeeControl Settings: Default
    Initial platform: Brim
    Print supports: Off
    Advanced Settings: Default
    • Total print time 30 minutes
    • Total filament 1 m
    • Additional non-printable components
    • Printed all at once
    Cubic

    Cubic

    Cubic crystal
    CCBYSA

    Recommended print settings

    Print profile: Speed
    Initial platform: None
    Print supports: On
    Advanced settings: Default
    • Total print time 60 minutes
    • Total filament 4 m
    • Additional non-printable components
    • Printed all at once
    Czech republic map base

    Czech republic map base

    Cartogram

    The base of the map of the Czech republic is part of a set containing other elements such as country-wide districts, districts showing unemployment rates and legend keys. This model has a representation of unemployment in the various Czech Republic districts using different heights.
    CCBYSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Default
    • Total print time 8 hours
    • Total filament 20 m
    • Additional non-printable components
    • Printed all at once
    DEATHCAP

    DEATHCAP

    The Deathcap has an olive green to brownish cap, which is hemispherical in the young fruiting body, then arched to flat in the older fruiting body. In the white form of this species, the cap may be pure white. The underside of the cap has white gills. These are covered by a partial veil in the young fruiting body, which remains in the form of a smooth or grooved ring on a cylindrical shaft in older fruit. The stipe is of varying deep green colour on a white ground. When young, the fruiting body is enveloped by a white universal veil, the remnants of which remain on the adult as a white volva at the base of the stipe. The flesh is white. The Deathcap is a deadly poisonous mushroom. It is abundant in deciduous forests and can be found alone or in groups under oaks, hornbeams, or beeches, for example.
    Models of the Deathcap depict different stages of fruiting body development - one model shows a young fruiting body covered by a partial veil and the other a mature fruiting body. An important part of the adult model is the volva, which is only attached to the stipe; sticking it on would prevent the two halves of the fruiting body from separating. The gills, ring, and volva should be painted white, the stipe can be given a slightly green tinge and the hat should be shaded green.
    CCBYSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Brim
    • Total print time 34 hours 22 minutes
    • Total filament 160.23 m
    • Additional non-printable components
    • Printed all at once
    Dice with Sharp Edges

    Dice with Sharp Edges

    DICE

    This is a common cube dice with sharp corners and edges. The sum of the numbers on opposing sides is 7.  
    CCBYNCSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Set roof and bottom thickness to 1.2mm. Set shell thickness to 1.2mm
    • Total print time 2 hours 15 minutes
    • Total filament 4 m
    • Additional non-printable components
    • Printed all at once
    Digital sculpture of Humpty Dumpty

    Digital sculpture of Humpty Dumpty

    Humpty Dumpty

    A printable digital sculpture of Humpty Dumpty, a character based on the popular nursery rhyme. Does not require supports.
    CCBYNCSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Default
    • Total print time 4 hours
    • Total filament 5.5 m
    • Additional non-printable components
    • Printed all at once
    Ditrigonal

    Ditrigonal

    Ditrigonal crystal
    CCBYSA

    Recommended print settings

    Print profile: Speed
    Initial platform: None
    Print supports: Off
    Advanced settings: Default
    • Total print time 9 hours
    • Total filament 67 m
    • Additional non-printable components
    • Printed all at once
    Dodecahedron connector

    Dodecahedron connector

    3D connector to contstruct different shapes using wooden dowl rods (or other suitable materials)

     

    CCBYSA

    Recommended print settings

    DeeControl Settings: Default
    Initial platform: Brim
    Print supports: Off
    Advanced Settings: Default
    • Total print time 30 minutes
    • Total filament 1 m
    • Additional non-printable components
    • Printed all at once
    Earthquake Shaker Table

    Earthquake Shaker Table

    Earthquake Simulation

    Earthquake shaker tables are useful in seismic research. The table can mimic motions of an earthquake so that structures can be subjected to the conditions of true ground movements. All parts should be scaled to 80% to fit the print area of the eDee 3D printer. Assembly is easy.
    CCBY

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: Default
    • Total print time 17 hours
    • Total filament 39 m
    • Additional non-printable components
    • Printed all at once
    Easy to Use Key Turner

    Easy to Use Key Turner

    Key Turner

    Insert a key in this key turner to make using a key easier by those with a disability. This model needs to be tough enough, so it won't break easily. Use 3 or more perimeters and add some top and bottom layers to provide maximum toughness.
    CCBYNCSA

    Recommended print settings

    Print profile: Default
    Initial platform: None
    Print supports: Off
    Advanced settings: 0.2mm layer height 1.2 mm shell
    • Total print time 40 minutes
    • Total filament 2.35 m
    • Additional non-printable components
    • Printed all at once